timing chain tensioners. 3 Remove the timing chain tensioner arms. Remove the timing chains and crankshaft sprocket. Remove the timing chain guides. 1 Remove the bolts. 2 Remove the LH timing chain guide. 3 Remove the bolts. 4 Remove the RH timing chain guide. Installation CAUTION: Timing and procedures must be followed exactly or damage to  valves and pistons will result.  Compress the tensioner plunger, using a vise. Install a retaining cl…

…st camshaft pulley. Loosen the exhaust camshaft pulley bolt. Loosen the intake camshaft pulley bolt.2. NOTE: Rotate the camshafts clockwise as necessary. Install the camshaftalignment timing tool on the back of the camshafts. 3. NOTE: Cylinder No. 1 is at top dead center (TDC) when the keyway is in the12 o’clock position. Confirm the crankshaft position is at the TDC. CAUTION: Do not rotate the crankshaft; as necessary check that it is stil…

1997 Ford Truck F 150 2WD Pickup V8-5.4L SOHC VIN L Installation Timing Chain Procedure: Compress the tensioner plunger, using an edge of a vise. CAUTION: Timing chainprocedures must be followed exactly or damage to valves and pistons will result. Donot compress the ratchet assembly. This will damage the ratchet assembly. Use a small screwdriver or pick to push back and hold the ratchet mechanism. While holding the ratchet mechanism, push the r…

nment. Using Pulley Holder (SST 09213-70010) and Handle (SST 09330-00021), hold crankshaft pulley.  Remove crankshaft pulley bolt. Using puller, remove crankshaft pulley. Remove bolts and crankshaft position sensor. See Fig. 5 . Remove bolts/nuts and accessory drive belt  tensioner. Remove bolts and right (timing chain side) engine mount bracket from front of cylinder block. Remove bolt and timing chain tensioner from side of timing chain cover…

…lb, 22 N.m) INSTALL CRANKSHAF T TIMING PULLEY Using SST and llarnllîlelr5 drive in the pulley. SST 09214-60010 TEMPORARILY INSTALL IDLER PULLEY AND TENSION SPRING (21) Install the idler pulley and tension spring. Torque: 500 kg-cm (36 It-lb, 49 Nm) Pry the idler pulley toward the left as far as it will go and temporarily tighten it. NOTE: Remove any oil or Water on the idler pulle}I and keep it clean. TEMPORARILY INSTALL TIMING BELT CAUTIO…

…ed, remove timing belt and reinstall. Rotate crankshaft clockwise 1 and 7/8 revolutions and align crankshaft pulley “0″ mark with 45-degree  Before Top Dead Center (BTDC) mark on No. 1 timing belt cover. See Fig. 5 . Tighten No. 1 idler pulley bolt to specification. See TORQUE SPECIFICATIONS . Install No. 2 timing  belt cover and gaskets. Install and tighten spark plugs to specification. To install remaining components, reverse remo…

le holding camshaft with camshaft sprocket holder. See TORQUE SPECIFICATIONS . Align camshaft sprocket timing mark with pointer. Properly position crankshaft so timing mark aligns with notch in front cover casting. See Fig. 2 . Remove the distributor cap, and ensure that the distributor rotor is facing the No. 1 position. Install timing belt over crankshaft sprocket, then counterclockwise over auxiliary shaft and camshaft sprockets. Loosen be…

1937 Toyota supra  DOHC Timing Belt  Service and Repair REMOVAL OF TIMING BELT 1. REMOVE RADIATOR  2. REMOVE SPARK PLUGS 3 REMOVE WATER OUTLET Remove the two bolts, Water outlet and thermostat with the gasket.  1937 Toyota supra Timing Belt Service and Repair 4. REMOVE AJC BELT 5. REMOVE FAN AND ALTERNATOR DRIVE BELT  6. REMOVE PS BELT 7. REMOVE NO3 TIMING BELT COVER Remove the flve belts5 nut and No.3 timing belt cover with the gasket…

1937 Toyota supra  DOHC Timing Belt  Service and Repair REMOVAL OF TIMING BELT 1. REMOVE RADIATOR  2. REMOVE SPARK PLUGS 3 REMOVE WATER OUTLET Remove the two bolts, Water outlet and thermostat with the gasket. 4. REMOVE AJC BELT 5. REMOVE FAN AND ALTERNATOR DRIVE BELT  6. REMOVE PS BELT 7. REMOVE NO3 TIMING BELT COVER Remove the flve belts5 nut and No.3 timing belt cover with the gasket. 8. SET NO.l CYLINDER AT TDC/COMPRESSION (21) Tur…

m, 80ft.lbf) INSTALL CAMSHAFT TIMING PULLEY Align the camshaft knock pin with the knock pin groove of the pulley, and slide  on the timing pulley. Using SST, install the plate washer and bolt. SST: 09249-63010 and 09276-  54012 Torque: 37 N.m (380 kgf.cm, 27 ft.lbf) HINT: Use a torque wrench with  a fulcrum length of 340 cm (13.39 in.) SET NO.1 CYLINDER TO TDC/COMPRESSION Turn the crankshaft pulley, and align its groove with timing mark &#…